Urethane Aliphatic A+B – Floor, Shower, Countertop, Concrete slab, Outdoor

Key Features:

• Surface Compatibility: Suitable for all surfaces, especially recommended for wet area shuch as: shower, sink, floor, countertop, concrete slab, and outdoor.
• Finish Options: Clear – Matte and Satin finishes . 4L Are also available in Medium Grey .4L custom color on order of 100L +. Contact a sale representative
• Size: 1.156 L and 4 L
• Coverage: up to 140 ft2/L with coverage varying based on surface porosity, application tools, and thickness applied.
• Drying Time Between Coats: 4 to 24 hours (accelerate with fan).
• Pot Life: 25 minutes.
• Number of Coats: Apply 2 to 4 coats for optimal protection. Add more as necessary.
• Application Tools: Foam Roller kit with Brush, Urethane Mixing Paddle on a drill, Disposable Measuring cup,  7-liter bucket, and Blue Masking Tape.
• Cleaning of Tools: Clean tools with water when the product is still fresh. Most of the time, it is difficult,  sometimes even impossible, to effectively preserve the brush, roller, and roller pan after each use.
• Final coat Drying Time: Light use of the surface after 12 to 24 hours, full drying achieved after 7 days.
• Usage: Suitable for both indoor and outdoor applications.
• Shelf Life: 12 months following the production date if stored in a dry and temperate area.
• Storage: Keep in a dry area at a temperature between 15°C and 25°C away from sun exposure.

Approved for Commercial Use:

• Hospitals, healthcare centers, educational establishments, grocery stores, shopping centers, commercial/industrial premises, restaurants, food processing plants, etc.

Surface Preparation:

• Ensure surfaces are clean, dry, and free of contaminants that could affect bonding.
  Apply Blue Masking Tape to adjacent surfaces.

Urethane Preparation:

• RATIO A: 4 = B: 1 + 8% to 10% WATER.
• Before initiating the mixing process, it is recommended to verify that all preparations are completed to prevent any time wastage post-mixing. Efficient application is essential once components A and B are mixed, given the product’s rapid setting characteristics.
• Prior to use, it is essential to thoroughly shake or mix components A and B individually to ensure even distribution of the matte or satin chemical throughout each portion.
• Prepare only the necessary quantity for each coat, always respecting the ratio and adding water inside a Disposable mixing cup.
• Mix with a  Urethane Mixing Paddle on a drill set to low speed(300 to 400 rpm).
• Add water into the vortex and keep mixing for at least 3 minutes until complete homogeneity.
• Use within 25 minutes following the mixing of the two components A and B.

Urethane Application:

• Ventilate the room during application.
• Do a test on a small section before proceeding.
• Apply the Urethane using a Foam Roller kit with Brush, for larger surface, you can use a standard size foam or 5mm roller .
• It is essential to apply each coat meticulously to ensure that all pores in the Microcement are thoroughly sealed.
• To prevent uneven protection and potential surface damage, avoid reapplying over areas that were coated a few minutes earlier, as this could cause the urethane to stick to your brush or roller.”
• For wall or countertop applications, ensure a minimum drying time of 4 hours between coats. For floors where walking is necessary during application, allow 12 to 24 hours between coats.
• If exceeding 24 hours, lightly sand with a 220 Sandpaper and remove dust using a dry cloth.
• Apply a minimum of 2 coats, and up to 4 coats for enhanced protection. Add more coats as needed until the waterproofing test confirms success.
• Remove the Blue Masking Tape.

Waterproofing test :

• 24 hours after the last urethane coat, always conduct a waterproofing test before using the surface.
• Do not proceed and use the surfaces until the waterproofing test is successful.
• To perform the test, use a soaking wet cloth and place it on various spots across the covered area for 15 minutes.
• If the color of the Microcement darkens, the surface is not adequately sealed and requires additional coat of urethane, wait until thoroughly dry to proceed. Repeat test until successful.
• If the color remains unchanged, proceed to conduct a thorough water test, such as running a shower or applying a substantial amount of water.
• If the color remains consistent after this test, the surface is properly sealed and ready for use.

Surface Maintenance:

• Avoid using the surface for the first 12 hours.
• Clean using only neutral soap to preserve the urethane coating and finish.

Safety Guidelines:

• Keep out of reach from children.
• Use in ventilated area, wear eye protection, gloves, and a mask. Wash hands after use.

Concrete Art Coating Aliphatic Urethane: Where Protection Meets Perfection!

Refer to the project type installation guideline and product label for more information

Installation Videos and Guidelines